Forum Home > HHO cell design > Calculate cell output | ||
---|---|---|

Moderator Posts: 1 |
It has been deduced from Faraday's laws that one ampere of current for one hour should produce .0147 cubic feet of hydrogen. (Paraphrased from "The Chemistry and Manufacture of HYDROGEN" by P. Litherland Teed - page 131. LONDON Edward Arnold 1919); this book being obtained from http://www.knowledgepublications.com. This equates to: amps X .000245 = CFM hydrogen. The equation I received from an electrochemical engineer I'm acquainted with is: amps X .000246 = CFM hydrogen, and amps X .0001229 = CFM oxygen. The accepted unit of measure of gas output that we use for the HHO cells we work with is LPM (liters per minute). To convert our calculated CFM of gas to LPM we multiply CFM by 28.3. For an example: assume a cell of one anode and one cathode (one gap between them) operating at 12 volts and consuming 12 amperes. Generated hydrogen would be 12 amps X .000246 = .002952 CFM, generated oxygen would be 12 amps X .0001229 = .0014748 CFM. Add the two together and multiply by 28.3 and we have .1253 LPM or 125.3 ml/min HHO. We see that this cell doesn't produce much HHO and being the plate to plate voltage is 12, we know we have a really good hot water heater. Practical experience tells us that plate to plate voltage should not be much over 2 to minimize heat gain. To achieve this in our test cell we must add 5 bi-polar (or commonly referred to as neutral) plates for a total of 7 plates having 6 gaps between them. The voltage is now reduced between each plate to 2, 12 volts divided by 6 gaps, however the current remains at 12 amps between each plate. Having 6 gaps at 12 amps each we now plug 72 into our equations; {(72 X .000246 =.017712) + (72 X .0001229 =.0088488)} = .0265608 X 28.3 = .7516 LPM = three quarters of a liter per minute at 12 amps, not bad and very little heat gain. We can increase our gas volume, along with current consumption, without additional heat gain, by connecting two or more of our seven plate cells electrically in parallel. When I first came upon these equations, I wondered how close they were to the real world. Through empirical testing on the calibrated flow bench, of several different cells, I found that these equations are accurate. Some cells getting closer to calculated output than others, none going over, due most likely to efficiencies of design. There are many parameters involved when designing a cell; gas quantity desired, sustained current available, and space required for mounting are primary concerns. We now see how we can calculate gas volume using available current. When designing for space requirements we need to consider how much current will be passing each plate. Heat generation results from a combination of voltage and current. We have seen that voltage can be controlled by the number of plates we use in each cell. We can control current by external means by using a pulse width modulator (PWM), there are some very good ones available. However, in the design process of our cell, by juggling the amount of parallel cells, the current to be used and the size of the plates, we are able to get a pretty good handle on the heat gain we will experience. An important consideration is current density on each plate in the cell. A good rule of thumb is to try to achieve a current density of .5 amps per square inch or less. In our test example above running at 12 amps, in order to achieve our .5 amps /sq. inch, since we have 12 amps flowing through each plate, we'll need plates equaling 24 sq. inch each. Possibly 3 X 8 inches or maybe 4 X 6 inches. If we have room and can make the plates larger, all the better, it will lower the current density and or allow for the use of more current thus producing more gas. As we have seen, we are able to closely calculate the expected HHO output of cell designs, albeit there are many factors to consider when starting with a clean sheet of paper.
| |

| ||

Member Posts: 1 |
I have used these Faraday calculations to build a Windows Program that reliably calculates the LPM of HHO, H, and O produced by anyones Cell. Input the operating voltage, number of plates, number of stacks, and it will predict plate voltage. Input the size of the plates and it will predict Maximum Current Density of the plates Active water surface area. Input an operating amperage and it will calculate the LPM. It has been tested on many different companies cells and used to backup their stated LPM @ their stated operating amps. If it works for one company, why should it not work for most all companies. This program is a free download at http://hho4free.com. ; In addition, it calculates Tubes, O-Ring gaskets, Rectangular gaskets, Unipolar Cells, Bipolar Cells, and Tube Cells. Even wire cells. | |

--
| ||